What Is an FD30 Fire Door? A Plain-English UK Guide

What Is an FD30 Fire Door?

An FD30 fire door is a fire-resisting door assembly that, when tested to BS 476-22 or BS EN 1634-1, holds back fire and (depending on specification) smoke for at least 30 minutes. The "FD" stands for "fire door"; the "30" is the time, in minutes, of fire resistance.

You'll see two common variants:

  • FD30 — 30 minutes integrity (E30) against fire only
  • FD30S — 30 minutes integrity plus cold-smoke seals (the "S")

For most residential applications in the UK — including flat entrance doors and corridor doors in blocks of flats — the relevant specification is FD30S.

How an FD30 Fire Door Works

A fire door is not just a thicker door. It's a tested assembly of components that work together:

  • A solid fire-resisting leaf (typically 44–54 mm thick)
  • A certified frame with the correct rebate depth
  • Intumescent strips that swell at around 200 °C to seal the gap between leaf and frame
  • Cold-smoke seals (FD30S only) — brush or fin seals that block smoke at room temperature
  • Certified hinges (usually three CE-marked fire hinges)
  • A self-closing device that fully latches the door from any open angle
  • Certified glazing if the door has a vision panel

Change any one of these for an unevidenced alternative and the certification is void. That's why FD30 fire doors are tested as a complete system, not piece by piece.

Where Are FD30 Fire Doors Legally Required?

Approved Document B and BS 9999 set out where FD30 (or higher) doors are required, but the most common scenarios are:

  • Flat entrance doors in blocks of flats — must be at least FD30S under the Fire Safety Act 2021
  • Doors onto protected escape routes — corridors, stairwells, lobbies
  • Doors between flats and common parts in HMOs
  • Plant rooms, storage cupboards and risk rooms in commercial buildings

Where higher resistance is needed — typically taller buildings, commercial risk rooms or stairwells in HMOs of certain sizes — FD60 fire doors (60-minute resistance) are specified instead.

How to Identify a Genuine FD30 Fire Door

A certified FD30 fire door will carry one of:

  • A top-edge label stamped with the fire rating, manufacturer and certification scheme
  • A colour-coded plug in the top edge of the leaf (BWF Certifire scheme)
  • A manufacturer's label on the frame

If there is no label, no plug and no documentation, the door cannot be assumed to be FD30. Our guide to fire door labels and identification walks through what to look for.

Common FD30 Failures We Find on Inspection

In our day-to-day fire door inspections across Lincolnshire and the East Midlands, the same FD30 defects come up over and over:

  • Gaps over the 3 mm tolerance specified in BS 8214
  • Missing or painted-over intumescent strips
  • Self-closing devices that close to a position but don't fully latch
  • Glazing replaced with non-fire-rated glass
  • Hinges replaced with standard, non-fire-rated alternatives
  • Doors held open with wedges instead of electromagnetic hold-open devices

Any one of these means the door is no longer FD30 compliant and must be remediated.

FD30 Fire Door Installation

A correctly specified FD30 door set is only as good as its installation. Under BS 8214, installation tolerances are tight:

  • 3 mm maximum gap between leaf and frame on the head and sides
  • 8–10 mm typical gap at the threshold (or as per manufacturer)
  • Intumescent strips fitted in the correct location (frame or leaf)
  • Hinges screwed with steel screws into solid timber pads or fire-rated fixings

This is why BM TRADA Q-Mark certified installation matters — it's third-party verified that the assembly was installed in line with the test evidence.

Stark Contracts FD30 Door Sets

Every FD30 and FD30S door set we assemble in our Lincoln workshop is supplied with:

  • BM TRADA Q-Mark or equivalent third-party certification
  • Top-edge identification plug
  • Component data sheets for every part of the assembly
  • Optional pre-fitted ironmongery and intumescent strips

For pricing, browse our pre-hung FD30 door sets, or call 01522 775570 to discuss a project.