DoorVision 3D for Main Contractors — Cutting Variations and Snagging on Fire Door Packages

The variation problem on fire door packages

Ask any commercial manager on a UK main contractor's site team to list the top three packages for variations, and fire doors will almost always be on the list. Wrong handing, wrong finish, missing intumescent, wrong architrave profile, glazing in the wrong leaf — every one of those errors becomes a variation, a remedial, or both.

DoorVision 3D — the UK's only real-time 3D fire doorset configurator — exists to take that argument off the table.

Where the variation usually starts

On most schemes the fire door package is specified by the architect against a 2D schedule, tendered to two or three manufacturers, sampled, signed off, and ordered. By the time the doors arrive on site, the design team, the contractor and the manufacturer have each made small assumptions about what the schedule actually meant. The first time anyone sees the doorset in three dimensions is when it comes off the lorry.

If the assumption was wrong, the contractor pays — either in a variation back to the client, a remedial back to the manufacturer, or programme slippage while the right set is built.

How main contractors use DoorVision 3D

  1. At tender stage. The fire door package is specified in DoorVision 3D. The captured images form part of the tender pack. There is no ambiguity about what the contractor is pricing.
  2. At pre-construction. The contractor opens the model with the client and the architect. The kit of parts is agreed in a single session. Variants are captured and archived against the package.
  3. At order. The captured images ship with the purchase order to Stark's BM TRADA Q-Mark certified Lincoln workshop. The workshop builds exactly what was signed off.
  4. On site. Doorsets arrive pre-hung, fire rated and ready to fit. Sub-contracted installers receive the captured image with each set. Snagging on the fire door package drops to near zero.
  5. At handover. Captured images are archived against the building file as part of the Building Safety Act Golden Thread.

The commercial case

Main contractors who have used DoorVision 3D on programmes report:

  • 30–50% fewer variations on the fire door package.
  • Sample drawing loop eliminated — typically saving 2–3 weeks per package against the original programme.
  • Snagging items reduced because the captured spec leaves no room for "I thought it meant…".
  • A defensible audit trail for the Building Safety Regulator on higher-risk buildings.

On a 200-unit Build-to-Rent block specifying around 800 doorsets, the saved time and removed variations typically run into tens of thousands of pounds.

Risk on the contractor's books

Under the Regulatory Reform (Fire Safety) Order 2005 and the Fire Safety (England) Regulations 2022, the responsibility for a non-compliant fire door rests with the Responsible Person — but the contractor's name is on the workmanship warranty and the practical completion certificate. A defensible record of what was specified, what was supplied and what was installed is in the contractor's interest as much as the client's. DoorVision 3D produces that record automatically.

What contractors need to do nothing about

DoorVision 3D runs in any modern browser. There is nothing to install, no software seat to buy, no integration to sit on the IT department's roadmap. Site teams, design teams and supply chain teams all use the same link.

A typical contractor session

A regional contractor running a 60-flat refurbishment in the Midlands recently used DoorVision 3D for the first time. The session ran for 35 minutes:

  • 0–10 min — design team configured the four standard flat entrance variants.
  • 10–20 min — site team reviewed and confirmed reveal depths and threshold details.
  • 20–30 min — client approved finish, ironmongery and signage.
  • 30–35 min — captured images saved to the project drive; PO raised against Stark.

Production started the same week. The traditional route would have taken a month to reach the same point.

How to roll it out

  1. Pick a single live package as a pilot — ideally a residential refurb or a BTR floor plate.
  2. Open DoorVision 3D with the design team and lock down the kit of parts in one session.
  3. Issue the captured images alongside the PO to Stark. Standard FD30 sets lead 3–4 weeks; FD60 sets 4–6 weeks.
  4. Repeat on the next package with confidence.

Further reading

Want to pilot DoorVision 3D on a live package? Call 01522 775570 or email Enquiries@Starkcontracts.co.uk. A Stark specifier will run a 30-minute session with your design and commercial team.