DoorVision 3D for Architects and Specifiers — A 15-Minute Tour
Designed for the people specifying the doors
If you specify fire doors for a living — RIBA-stage 4 architect, M&E consultant, design-and-build contractor — DoorVision 3D was built for you. It is the UK's only real-time 3D fire doorset configurator, developed in-house by Stark Contracts Ltd, and it lives on our pre-hung doorsets page.
This is the 15-minute tour.
Minute 1–3: Pick the assembly
Open the configurator. Pick FD30 or FD60. Pick single or double leaf. Pick the structural opening dimensions. The base assembly renders in 3D in front of you — frame, leaf, hinges, lock, intumescents, seals — all to scale, all photoreal.
Specifiers often start with the most common opening on the scheme (a flat entrance door, an apartment corridor door, a hospital ward door) and tune from there. Within three minutes you have a base assembly that already matches 70–80% of the openings on the scheme.
Minute 4–7: Finish, ironmongery, glazing
Cycle through the finish options — oak, walnut, sapele, ash, primed paint-grade, full RAL palette. The leaf re-renders in real time. Pick the ironmongery package — lever-on-rose, lever-on-backplate, kickplate, closer, finger guard, drop-down seal. Drop in a vision panel if the scheme calls for one, size it, position it. The fire-rated glazing renders at the correct depth in the leaf with intumescent glazing tape modelled behind the bead.
By minute seven you have a fully specified BM TRADA Q-Mark fire doorset on screen.
Minute 8–10: Capture and annex
Orbit the camera to the angle you want for the tender package. Capture the view as a high-resolution image. Drop the image into the doorset schedule annex of your tender or technical submission. The contractor pricing the package now sees exactly what is required — no interpretation, no "as per supplier's standard", no week-long clarification cycle.
Minute 11–13: Variants
Most schemes need three or four configured doorset types to cover 95% of openings. Re-open the configurator, change the parameters that differ (handing, glazing, finish), capture a fresh image. Within five minutes you have a complete "kit of parts" — the four images that will drive the entire fire door programme on the scheme.
Minute 14–15: Order or hand off
Drop the configured sets straight into the order form on the same page — DoorVision 3D and the order form share state. Or hand the captured images and parameters to the main contractor to procure under their package. Either way, the doorset that arrives on site matches the image you captured.
Why this matters at RIBA stage 4
At RIBA stage 4 (Technical Design) the fire door schedule is typically the last package to lock down — because traditionally it has required two-week sample drawing loops with the supplier. That timing pushes fire door clarifications into stage 5 (Manufacturing and Construction), where they collide with the construction programme.
DoorVision 3D lets you lock the package down inside stage 4. No sample drawing loop. No "TBC pending supplier confirmation" in the schedule. The captured images sit in the tender package; the contractor prices a fully specified package; the supplier (Stark) builds to the captured image.
Why it matters under the Building Safety Act
The Building Safety Act 2022 makes the Principal Designer responsible for managing design-stage building safety information. The captured DoorVision 3D image is that information — a timestamped, version-controlled record of the exact specification approved at design stage. It travels with the order, the manufacture log, the install record and the post-occupancy inspection record. One Golden Thread, four touchpoints, one image.
What we do not promise
- DoorVision 3D does not replace the BS 8214:2026 standard or the manufacturer's published installation instructions. It models the assembly to the manufacturer's spec; the installer must still install to those instructions.
- DoorVision 3D does not auto-generate fire risk assessments. The fire risk assessor still needs to assess the building.
- DoorVision 3D does not commit you to anything. Capture as many images as you like. Order when you are ready.
How to get started
- Open the 3D configurator. No login, no email gate.
- Specify a representative set from your scheme. Capture the view.
- Send the image and parameters to Stark for a project-level quote — call 01522 775570 or email Enquiries@Starkcontracts.co.uk.
- Place the order through DoorVision 3D when you are ready. Standard FD30 sets lead 3–4 weeks; FD60 sets 4–6 weeks; phased deliveries available against the construction programme.
Further reading
- Pre-hung fire doorsets — main page and DoorVision 3D
- Introducing DoorVision 3D — the UK's only real-time fire door configurator
- Inside DoorVision 3D — how the configurator works
- Why DoorVision 3D saves days on every fire door programme
- Nationwide pre-hung doorset supply
Lock down your doorset package in 15 minutes. Open DoorVision 3D or call 01522 775570 for a guided walk-through with one of our specifiers. The only real-time 3D fire door configurator in the UK, built in Lincoln by Stark Contracts Ltd.