Fire Door Frames: Why the Frame Is Half the Fire Door
The frame is not an accessory
A fire door is tested as an assembly. Around half of that assembly is the frame: the jambs, head, planted or rebated stop, seals and the fixings that tie it to the structural opening. Fit a perfect certified leaf into the wrong frame and you no longer have a certified fire door — you have an uncertified assembly with a label on it.
This is why we supply pre-hung doorsets wherever a client will accept them. A factory-hung doorset arrives as one certified unit — leaf, frame, seals and ironmongery preparation matched — and removes almost every failure mode described below.
Material and section
Fire door frames are normally solid timber, with hardwood used where durability or a higher rating demands it. Metal frames are used for steel doorsets and in certain commercial applications, tested as their own systems.
Typical timber frame requirements:
- A minimum section stated in the certification — often around 32 mm thick for FD30 and 45 mm or more for FD60.
- A minimum density for the timber species; a light softwood may be excluded by the certification even at the right dimensions.
- A stop depth of at least 25 mm for FD30 assemblies, and commonly deeper for FD60. The stop is what the leaf shuts against and what the expanding seals bear on.
- The stop should be rebated from solid or, where planted, fixed at the centres and with the fixings stated in the installation instructions.
Intumescent seals in the frame
Seals may be housed in the leaf edge, the frame, or both — again, the certification decides. What matters at inspection is that they are:
- Continuous around the head and both jambs, with neat mitred or butted corners and no gaps at joints.
- The correct size and type (single or twin strip, with or without a smoke brush or fin for an "S" rated door).
- Undamaged, unpainted and fully seated in their grooves.
Painted-over seals are extremely common in older housing stock and are recorded as a defect because the paint film can prevent proper expansion and, more importantly, indicates the door has been decorated without regard to its rating.
Fixings and packing — where installs go wrong
The frame must transfer load into the structural opening and stay in place while the door distorts. BS 8214:2026 practice requires:
- Fixings of the specified type and length — usually steel screws or frame anchors, not nails, and never foam alone.
- Fixings at the specified centres, typically within about 150 mm of each corner and then at regular intervals down each jamb, with fixings adjacent to hinge and lock positions.
- Solid packing at every fixing point so the frame is not pulled out of line as screws are tightened. Packers must be non-combustible or intumescent-protected as the instructions require, and they must be permanent.
- The perimeter gap filled correctly. The void between frame and structural opening is a real fire path. It must be filled to the certification — commonly mineral wool with an intumescent acrylic seal, or an approved fire-rated foam. General-purpose expanding foam is not acceptable and is one of the most frequent installation failures we find.
- Architraves fitted after the perimeter seal, never used to hide an unsealed gap.
Can you reuse an existing frame?
Sometimes — but only with evidence. If a new certified leaf is being hung, the manufacturer's certification will state what frame it may be used with. Reusing an existing frame is acceptable only where its material, section, stop depth and condition meet that specification and the seals can be correctly accommodated. In older properties the existing frame frequently has an undersized stop, historic damage, or ten coats of paint in the rebate, and replacement as a full doorset is the honest answer.
Frame defects we record most often
- Stop depth below the certified minimum.
- Split, crushed or rotten jambs, especially at strike plates and low-level impact points.
- Missing or foam-only perimeter fill behind architraves.
- Frames bowed between fixings, producing gaps well over 4 mm at mid-height.
- Loose frames that move when the door slams.
- Non-fire-rated strike plates or unfilled recesses from removed ironmongery.
The pre-hung alternative
Because the frame is where most site errors occur, we manufacture pre-hung FD30 and FD60 doorsets to size, with seals, hinges and ironmongery preparation completed under factory control. Installation becomes a single, repeatable operation, and the certification covers the whole unit.
Talk it through on 01522 775570 or Enquiries@Starkcontracts.co.uk.