Commercial Fire Doors: Specification, Duty Ratings and Compliance

What makes a commercial fire door different

The fire rating is the same language — FD30, FD60, with an S suffix for smoke — but the demands are not. A flat entrance door might see twenty cycles a day. A commercial corridor door can see several hundred. Everything that wears — hinges, closers, latches, seals, lippings — has to be specified for that duty, or the doorset becomes non-compliant long before its notional life is up.

Where fire doors are required in commercial buildings

The building's fire strategy and fire risk assessment govern this, but the usual locations are:

| Location | Typical rating | | --- | --- | | Protected stairways and lobbies | FD30S or FD60S | | Compartment walls between fire compartments | FD60 (matching the wall) | | Plant rooms, boiler rooms, sprinkler and switch rooms | FD60, often kept locked | | Service risers and ducts | FD30 / FD60, "keep locked" | | Refuse and bin stores | FD30 / FD60 | | Corridors on escape routes | FD30S, self-closing | | Kitchens and high-risk rooms | To the fire strategy |

The door rating must match the fire resistance of the construction it sits in. Fitting an FD30 door in a 60-minute compartment wall is a common and serious specification error.

Ironmongery: grade matters

For commercial duty, specify to the standards and to the cycle count:

  • Hinges — BS EN 1935, normally Grade 13 (200,000 cycles), CE/UKCA marked, three per leaf as a minimum unless the certification says otherwise.
  • Closers — BS EN 1154, sized correctly for leaf width and mass, and adjustable to meet Approved Document M opening forces (no more than 30 N through the first 30 degrees, 22.5 N from 30 to 60 degrees).
  • Locks and latches — BS EN 12209, fire-tested for use on the doorset.
  • Panic hardware — BS EN 1125 for public buildings; BS EN 179 emergency exit hardware where occupants are familiar with the building.
  • Electromagnetic hold-opens — BS EN 1155, interfaced with the fire alarm to BS 7273-4.

Under-specified closers are the single most common cause of a commercial door being propped: the door is too heavy, staff wedge it, and the compartmentation stops existing.

Your legal duties

Under the Regulatory Reform (Fire Safety) Order 2005, the responsible person — usually the employer, building owner or managing agent — must keep fire doors in efficient working order and in good repair. That duty is continuous, not annual. Breaches are prosecutable, with fines up to unlimited amounts on indictment and, in serious cases, imprisonment.

The Fire Safety (England) Regulations 2022 add specific, prescriptive duties for residential buildings with multiple domestic premises: quarterly checks of communal fire doors and annual best-endeavours checks of flat entrance doors in buildings above 11 m, plus resident information. Purely commercial buildings are not caught by those specific intervals, but the general duty to maintain still applies — and a risk-based inspection regime is how you demonstrate it.

How often should commercial fire doors be inspected?

Industry guidance, reflected in BS 8214:2026, is a competent inspection at least every six months for doors in general use, and more frequently for high-traffic doors — main entrances, busy corridors, doors near loading areas — with routine visual checks by site staff in between.

What you need on file is not just "we checked them". It is a per-door record: unique reference, location, rating, certification evidence, gap measurements, condition of seals and ironmongery, photographs, defects, and what was done about them.

Repair, remedial or replace

Most commercial defects are remediable: seals, hinges, closers, latches, signage, threshold adjustments and localised repair within the manufacturer's stated tolerances. Replacement is the right answer for uncertified doors, structurally damaged leaves, doors with undocumented modifications, and doors of the wrong rating for their wall.

Doing it once, properly

Stark Contracts surveys, installs and maintains certified FD30 and FD60 doorsets for offices, schools, care homes, retail and industrial sites across Lincolnshire and the East Midlands, with digital reporting and photographic evidence for every door. See fire door inspection and fire door maintenance, or call 01522 775570.